Instruction booklet. Supplied in carry case. Replaces stripped/worn threads in cylinder head for M8 x 1.0, M10 x 1.0, M10 x 1.25, M12 x 1.25 threaded glow plugs.
Thread Inserts: M8 x 1.0, M10 x 1.0, M10 x 1.25, M12 x 1.25 (5 of each)
Taps: M8 X 1.0, M10 X 1.0, M10 X 1.25, M12 X 1.0, M12 X 1.25, M14 X 1.25
Knurled Head
Insert Guide Rod
Tap Guide Pin: 8 x 45, 10 x 45, 12 x 45
Insert Driver: M8 x 1.0 & M10 x 1.0, M10 x 1.25 & M12 x 1.25
Designed to straighten out clamp dents in mufflers and tailpipes quickly and easily. A Simple wrench turn expands pipe for exhaust system repair and installation. A perfect tool for fitting after market rear boxes to a standard exhaust. This high quality Pipe Expander Set comes to you brand new with retail packaging/tag. Full set of 3 expanders to fit small, medium, large cars, 4 x 4’s and commercial vehicles. Expander Sizes:
Small Expander: 1-1/8″ to 1-3/4″
Medium Expander: 1-1/2″ to 2-1/2″
Large Expander: 2-1/8″ to 3-1/2″
Designed to identify and trace wires or cables without damaging the insulation. Also used for checking short circuit and locating open circuits etc… There is a sender and a receiver included in this instrument. Tracing of wires is made possible even inside bundles, conduits, behind panels, under carpets, upholstery etc… Simple to use simply connect the transmitter in series with the circuit or wire under test and then scan the circuit/wire with the tracers flexible probe to find the trouble spot. Only for use on DC voltage do not use on AC voltage.
Operates on DC voltages from 6 – 42 volts. Do not connect to circuit exceeding 42 volts DC. Do not use with any component or circuits of the ignition system. Internally protected against power surges and overloads. Adjustable sensitivity for all tracking situations. The probe of the receiver is built of coiled steel and may be bent as needed in order to reach wires in congested or difficult areas. For the best possible range, the receivers probe tip (black cap) should be positioned perpendicular (90 degrees) to the wire being traced. 7″ Flexible probe allows reaching wires in congested places. Transmitter and receiver LEDS show open or short circuit conditions. Powered off 2 x 9v batteries (Included) comes complete with a full set of instructions for accurate and quick use. Supplied in a storage case.
Chrome vanadium steel, heat-treated for strength and durability. Contains 3 most popular oxygen and vacuum switch sockets.
1 x Vacuum Switch Socket 3/8″ Dr. x 7/8″ x 80mm. Designed to remove and install oxygen sensors. Socket designed with slot which allows clearance of wire. Designed to be used with 3/8″ drive tool or 1″ wrench / spanner
1 x Heated Oxygen Sensor Socket 3/8″ Dr. 7/8″ x 50mm. Socket designed with slot in socket which accommodates the connectors on heat oxygen sensors. Socket has a double 1/2″ for easy access
1 x Offset Oxygen Sensor Wrench 3/8″ x 7/8″ x 30mm. Low profile design for use in tight spaces. Designed to be used with 3/8″ drive tool.
All stored in moulded case. The set Contains the following:
1 x Hose Clamp Pliers
1 x Swivel Jaw Spring Wire Clip Pliers
1 x Swivel Jaw Band Clip Pliers
1 x Angled Flat Band Hose Clamp Pliers
1 x Hose Remover Pliers
1 x Clic- R Collar Pliers
1 x Flat Band Hose Clamp Pliers
1 x Screwdriver
1 x Hose Remover
Designed to measure return fuel flow on diesel vehicles having up to 6 cylinders fitted with common rail injection system. Identifies, worn, blocked or inoperative injectors. Supplied with both measurement tubes and bottles for short or long term testing. 24 Injector adaptors for BOSCH, SIEMENS, DENSO and DELPHI injectors. Supplied in a blow moulded storage case. This high quality Flow Meter comes to you brand new with retail packaging. This is a perfect addition / replacement to any toolbox or workshop.
1/2″ drive so will fit any 1/2″ drive ratchets / bars / extensions etc. CR-MO with HRC50-53. Black phosphate finish for protection.
Size: T45
Length: 78mm
Forged from steel with black phosphate coating for protection. Hardened and tempered for enhanced durability. 1″ drive so will fit any 1″ drive ratchets / bars / extensions etc.
Size: 36mm
Points: 6
Total length of socket: 80mm
Outside diameter of socket end: 55mm
Outside diameter of drive end: 50mm
Hardened: HRC 38-42 for durability
Finish: Black phosphate for protection
A set of double ended ring spanners with a 75 degree offset. Made from chromium-vanadium steel for strength and durability and helps resist abrasion, oxidation, and corrosion. Mirror polish & Non-slip finish. Supplied with storage pouch.
Contains the following sizes:
6 x 7mm, 8 x 9mm, 10 x 11mm, 12 x 13mm, 14 x 15mm, 16 x 17mm and 18 x 19mm.
1/2″ drive so will fit any 1/2″ drive ratchets / bars / extensions etc. Made from chromium-vanadium steel for strength and durability and helps resist abrasion, oxidation, and corrosion. Industrial black phosphate finish. This high quality Socket comes to you brand new with retail packaging/tag. This is a perfect addition / replacement to any toolbox or workshop.
Size: T55
Length: 78mm
Extra long slim shafts. Mirror polished. Hardened and tempered. Ring head extends out from the shaft on one side. Double hex ring spanner on either end. Manufactured from the highest quality chrome vanadium steel 6140. Supplied in a canvas storage pouch
Sizes:
8 x 10mm (Approx. Length: 234mm)
11 x 13mm (Approx. Length: 329mm)
14 x 15mm (Approx. Length: 369mm)
16 x 17mm (Approx. Length: 409mm)
18 x 19mm (Approx. Length: 409mm)
1/2″ drive so will fit any 1/2″ drive ratchets / bars / extensions etc. Made from chromium-vanadium steel for strength and durability and helps resist abrasion, oxidation, and corrosion. Industrial black oxide finish. This high quality T50 Torx socket comes to you brand new with retail packaging/tag. This is a perfect addition / replacement to any toolbox or workshop.
Size: T50
Length: 78mm
Heavy Duty Webbing Strap. Strong CR-MO material. This high quality Oil Filter Strap Wrench comes to you brand new with retail packaging/tag. This is a perfect addition / replacement to any toolbox or workshop.
Size Range: 21 – 120mm
Drive: 1/2″
These screw extractors enable rounded or rusted hexagonal nuts, bolts or screws to be removed. Supplied in a storage case.
Sizes: 9, 10, 11, 12, 13, 14, 15, 16, 17, 19mm
Includes: 7mm x 90mm Round Bar
A Metric High Quality Drill Bit Set For Alloyed And Unalloyed Steels. With A Precision Ground Tip, Split Point And 135° Angle Makes These Din 338 Bits Very Precise For Centring During Spot Drilling. Suitable For Drilling Cast Iron, Iron, Non Ferrous Metals And Steel.
The Set Contains The Following Sizes: 2.0, 2.5, 3.0, 3.5, 4.0, 5.0, And 6.0mm
• Hss-g Xtra
• High Quality
• Din338 Standard
• Fully Ground
• 135 Degree Split Point
• Precise
• Durable
Supplied in zip-up pouch. This is a perfect addition / replacement to any toolbox or workshop.
Size: 325mm
1 x Straight External Pliers
1 x Straight Internal Pliers
1 x Bent External Pliers
1 x Bent Internal Pliers
This multi-purpose scratch brush is manufactured from a heavy duty construction with plastic grip & brass coated steel wire. Ideal for removing rust and paint also cleaning the BBQ and preparing metal surfaces.
Size: 23cm (approx.)
Comprehensive set of impact adaptors for use on all types of impact tools. Manufactured from drop-forged Chrome Vanadium steel, for the smaller sizes and Chrome Molybdenum for the bigger sizes, with phosphate finish for added corrosion protection. Spring ball socket retention. Industrial black finish. Supplied in tool case.
Sizes:
3/8″ (F) x 1/4″ (M) = CRV
1/4″ (F) x 3/8″ (M) = CRV
3/8″ (F) x 1/2″ (M) = CRV
1/2″ (F) x 3/8″ (M) = CRV
1/2″ (F) x 3/4″ (M) = CR MO
3/4″ (F) x 1/2″ (M) = CR MO
3/4″ (F) x 1″ (M) = CR MO
1″ (F) x 3/4″ (M) = CR MO
